MAX395EWG+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 8 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX395 |
| Output | SEPARATE OUTPUT |
| Pin Count | 24 |
| JESD-30 Code | R-PDSO-G24 |
| Operating Supply Voltage | 8V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 8 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 30μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 500 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 400ns, 400ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω (Max) |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Switch-off Time-Max | 400ns |
| Height Seated (Max) | 2.65mm |
| Length | 15.4mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX395EWG+T Overview
Due to its 24-SOIC (0.295, 7.50mm Width) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. In total, there are 24 terminations. This electronic part offers high-quality output due to its 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 24 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. There are 8 circuits in this multiplexer. Try searching with MAX395 if you're looking for variants. It has an internal resistance of 100Ohm. It is a typical Multiplexer or Switches analog multiplexer. Multiplexers should not be powered above 16V in normal situations. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 2.7V. A digital multiplexer may suffer damage if voltage is applied above 20μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 8V. It is recommended that you attach at least 3V to your dual power supply. This analog switch ic utilizes SEPARATE OUTPUT output. Operating voltages range from 8V.
MAX395EWG+T Features
1 Channels
Switch Circuit: SPST - NO
MAX395EWG+T Applications
There are a lot of Maxim Integrated MAX395EWG+T Analog Switches & Multiplexers ICs applications.
- DSUs
- Digital cross connects (DSX-1)
- Automatic test equipment
- Modems
- Cable PC
- Industrial control systems
- Data switching
- Fault Tolerant Systems
- ATM
- New designs requiring multiplexer functions
