MAX396CWI
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 28 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | TIN LEAD |
| Max Power Dissipation | 1W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX396 |
| Pin Count | 28 |
| Number of Channels | 16 |
| Interface | Logic |
| Number of Circuits | 1 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 60nA |
| Nominal Supply Current | 80nA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 80pF |
| On-state Resistance Match-Nom | 1.8Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.8 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Height | 2.35mm |
| Length | 18.1mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX396CWI Overview
Due to its 28-SOIC (0.295, 7.50mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. A switch device like this is mounted in Surface Mount. There is 16:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of 0°C~70°C TA degrees Celsius. There are 28 terminations totally. Due to its 16 channels, the electrical component produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 28 series, this electronic part has been incorporated into the system. There are 1 circuits in this switch device. Using the MAX396 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 100Ohm. You can find the functions of the 28 pins in the datasheets. It is generally not recommended to supply a voltage higher than 16V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended to use 2.7V as the lowest voltage for the electrical part. The analogue multiplexer could operate on 60nA current. For this switch, a dual supply voltage is feasible, but it must not exceed 8VWith dual power supplies, you should attach at least 3V.
MAX396CWI Features
16 Channels
60nA Supply Current
MAX396CWI Applications
There are a lot of Maxim Integrated MAX396CWI Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- Battery Powered Systems
- Data Acquisition Systems
- Industrial control systems
- Audio and video routing
- Automatic test equipment
- SDH
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Multi-Line E1 Interface Cards
- Imaging
