MAX396EWI
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 1W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX396 |
| Pin Count | 28 |
| Operating Supply Voltage | 15V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 80pF |
| On-state Resistance Match-Nom | 1.8Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.8 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Height | 2.35mm |
| Length | 18.1mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX396EWI Overview
Due to its 28-SOIC (0.295, 7.50mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. In Surface Mount, you'll find this switch device. There is 16:1 ratio between the number of multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. The total number of terminations is 28. This electronic part offers high-quality output due to its 16 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. A total of 28 pins are injected into the electrical part body. There are 1 circuits in this switch device. Try searching for the analog switch ic with MAX396 if you are looking for variants. As far as internal resistance is concerned, it has 100Ohm. The datasheets for the 28 pins explain the functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 16V. A cost-effective Dual, Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 2.7V. It would be sufficient to run this analogue multiplexer with 1μA current. If put voltage greater than 8V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 3V. The electronic component can function from 15V.
MAX396EWI Features
16 Channels
1μA Supply Current
MAX396EWI Applications
There are a lot of Maxim Integrated MAX396EWI Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- Automatic test equipment
- Power routing
- Modems
- Precision data acquisition
- PBXs
- E1 Network Equipment
- Residential Gateways, Home Gateway/Router
- E1 Multiplexer
- SONET
