Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
28-SSOP (0.209, 5.30mm Width) |
Number of Pins |
28 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2016 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
28 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
762mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Base Part Number |
MAX397 |
Pin Count |
28 |
Operating Supply Voltage |
15V |
Number of Channels |
8 |
Number of Circuits |
2 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1μA |
Propagation Delay |
150 ns |
Turn On Delay Time |
500 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
2.7V~16V ±2.7V~8V |
Supply Type |
Dual, Single |
Supply Current-Max (Isup) |
0.001mA |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
400 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
3V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
11pF 80pF |
On-state Resistance Match-Nom |
1.8Ohm |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
1.8 Ω |
Crosstalk |
-92dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.03A |
Height Seated (Max) |
1.99mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX397CAI+T Overview
Shipping overseas is convenient with the electronic component packed in 28-SSOP (0.209, 5.30mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 8:1. Temperatures around 0°C~70°C TA are extended for operation. In total, there are 28 terminations. Due to its 8 channels, the electrical component produces high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. An electrical component like this is included in the 28 series. A total of 2 circuits make up this switch device. Try searching with MAX397 if you're looking for variants. As far as internal resistance is concerned, it has 100Ohm. To find out what the functions of 28 pins are, please refer to their datasheets. Users should never supply a voltage higher than 16V to a switch device. Dual, Single supply type digital switch with a low cost. There should be 2.7V voltage fed to the electrical part below 2.7V. 1μA current would be enough for this multiplexer to operate. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 8V. In the case of dual power supplies, you should connect at least 3V. There is a voltage range of 15V operating voltages for the electrical part.
MAX397CAI+T Features
8 Channels
1μA Supply Current
MAX397CAI+T Applications
There are a lot of Maxim Integrated MAX397CAI+T Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- DSLAMs
- Industrial and process control systems
- CSU
- PBX interfaces
- Imaging
- High-Voltage
- Avionics and Military Systems
- Industrial
- Optical Applications