MAX397EPI
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Power Dissipation | 1.143W |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX397 |
| Pin Count | 28 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±2.7V~8V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.001mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 80pF |
| On-state Resistance Match-Nom | 1.8Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.8 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 5.08mm |
| Length | 36.83mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX397EPI Overview
The electronic part can be shipped overseas conveniently because it is packaged in 28-DIP (0.600, 15.24mm). This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. Around -40°C~85°C TA is the extended operating temperature. In total, there are 28 terminations. A 8 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. 28 pins are injected to the electronic part body. There are 2 circuits in this switch device. Use MAX397 to search for variants of the digital switches. As far as internal resistance is concerned, it has 100Ohm. Datasheets for 28 pin functions are available upon request. An abnormal situation would be for the switch device to be supplied with a voltage greater than 16V. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 2.7V. 1μA current would be enough for this multiplexer to operate. For this switch, a dual supply voltage is feasible, but it must not exceed 8VThe voltage should be at least 3V if you are using dual power supplies. The electronic component can function from 15V.
MAX397EPI Features
8 Channels
1μA Supply Current
MAX397EPI Applications
There are a lot of Maxim Integrated MAX397EPI Analog Switches & Multiplexers ICs applications.
- Precision data acquisition
- Remote Powered Equipment
- Data Acquisition Systems
- Isolation
- Data switching
- Battery Powered Instruments
- Battery Powered Systems
- PCMCIA cards
- Digital Cross-Connects
- Digital cross connects (DSX-1)
