MAX398CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX398 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 6 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX398CPE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. In Through Hole, you'll find this switch device. 8:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around 0°C~70°C TA. Total terminations are 16. As a result of its 8 channels, this electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. A 1 circuit is present in this switch device. MAX398 can be used to search for analog multiplexer variants. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Users shouldn't supply more than 15V voltage to the switch device. An effective Dual, Single supply digital multiplexer. There should be 3V voltage fed to the electrical part below 3V. This multiplexer would work with 1μA current. If put voltage greater than 8V on the multiplexer, damage may be caused to the device. If you are using dual power supplies, you should attach at least 3V. The electronic component can function from 12V.
MAX398CPE Features
8 Channels
1μA Supply Current
MAX398CPE Applications
There are a lot of Maxim Integrated MAX398CPE Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- Channelized and Unchannelized DS3 applications
- Fiber to the Home
- Digital access cross connects
- High reliability control systems
- Cable PC
- PDAs
- Residential Gateways, Home Gateway/Router
- Private Branch Exchange (PBX)
- Fault Tolerant Systems
