Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2002 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
225Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Base Part Number |
MAX398 |
Pin Count |
16 |
Operating Supply Voltage |
12V |
Number of Channels |
8 |
Number of Circuits |
1 |
Max Supply Voltage |
15V |
Min Supply Voltage |
3V |
Operating Supply Current |
1μA |
Throw Configuration |
SP8T |
Propagation Delay |
150 ns |
Turn On Delay Time |
500 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
3V~15V ±3V~8V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
400 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
3V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
11pF 40pF |
On-state Resistance Match-Nom |
6Ohm |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
6 Ω (Max) |
Crosstalk |
-92dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.03A |
Height |
1.5mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
MAX398CSE+ Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tube is used. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 8:1. Around 0°C~70°C TA is the extended operating temperature. The total number of terminations is 16. As a result of its 8 channels, this electronic component provides high-quality output. A 5V voltage supply should turn on and run the electronic component. It is part of the design of the 16 series that this electronic component is included. There are 1 circuits in this multiplexer. Try searching for the analog switch ic with MAX398 if you are looking for variants. The internal resistance of this digital multiplexer is 225Ohm. The datasheets for the 16 pins explain the functions. It is generally not recommended to supply a voltage higher than 15V to the switch device in normal circumstances. An effective Dual, Single supply digital multiplexer. 3V is the lowest voltage the electrical component should receive. An operating current of 1μA would be sufficient for this switch device. For this multiplexer, dual supply voltage is feasible, but it should not exceed 8V. You should attach at least 3V voltage if you are using dual power supply. It can operate from 12V operating voltages.
MAX398CSE+ Features
8 Channels
1μA Supply Current
MAX398CSE+ Applications
There are a lot of Maxim Integrated MAX398CSE+ Analog Switches & Multiplexers ICs applications.
- SONET
- High-Voltage
- SDH/SONET multiplexers
- Channel Banks
- E1 Multiplexer
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cellular phones
- Data Acquisition Systems
- Microprocessor controlled systems
- Optical Applications