MAX398CSE+TG55
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX398 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 6 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX398CSE+TG55 Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, you'll find this switch device. There is 8:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around 0°C~70°C TA. 16 terminations have been made so far. As a result of its 8 channels, this electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. There is an electrical component included in the 16 series. This multiplexer is composed of 1 circuits. Try searching with MAX398 if you're looking for variants. Analog switches have 100Ohm internal resistance. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 15V voltage to the switch device. There should be 3V voltage fed to the electrical part below 3V. Despite this switch device's dual supply capability, its voltage should not exceed 8V. If you are using a dual power supply, you should attach at least 3V. It is integrated with a SINGLE-ENDED MULTIPLEXER analog IC.
MAX398CSE+TG55 Features
8 Channels
MAX398CSE+TG55 Applications
There are a lot of Maxim Integrated MAX398CSE+TG55 Analog Switches & Multiplexers ICs applications.
- SDH
- E1 Network Equipment
- SONET
- Sample hold systems
- T1/E1 Terminals
- Transmit
- Central office
- Digital Cross-Connects
- Battery Powered Instruments
- USB 1.1 signal switching circuits
