MAX398ESE
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX398 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Throw Configuration | SP8T |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 6 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX398ESE Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a number of circuits 8:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. A electrical component with 8 channels is capable of high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. The electrical component body receives 16 pins. Circuits number 1 make up this analogue multiplexer. Try searching for MAX398 variants of the analog switch ic. It has an internal resistance of 100Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Users shouldn't supply more than 15V voltage to the switch device. A cost-effective Dual, Single supply type analogue multiplexer. 3V should be the lowest voltage fed to the electronic component. This multiplexer would work with 1μA current. If put voltage greater than 8V on the multiplexer, damage may be caused to the device. With dual power supplies, you should attach at least 3V. A voltage of 12V can be used to operate the electronic component.
MAX398ESE Features
8 Channels
1μA Supply Current
MAX398ESE Applications
There are a lot of Maxim Integrated MAX398ESE Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- Cross Connects
- Digital Cross-Connects
- Industrial
- SONET/SDH ADM
- Isolation
- High reliability control systems
- Battery Powered Instruments
- PBXs
- RGB switches
