MAX399EEE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 667mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Base Part Number | MAX399 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.001mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 20pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 6 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| On-State Resistance | 100Ohm |
| Height | 1.75mm |
| Length | 4.89mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX399EEE+ Overview
The electrical component comes in 16-SSOP (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 4:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. High-quality output is provided by the electronic component's 4 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. The electronic part body is injected with 16 pins. Unlike digital switches, these are based on SP4T switching circuits. It consists of 2 circuits. Try searching for MAX399 variants of the analog switch ic. This digital multiplexer has 100Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 15V. A analog switch ic that has a cost-effective Dual, Single supply type. 3V is the lowest voltage that should be fed to the electronic electronic part. The switch device would be able to operate with 1μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 8V. The voltage should be at least 3V if you are using dual power supplies. 12V operating voltages are supported by the electronic component.
MAX399EEE+ Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX399EEE+ Applications
There are a lot of Maxim Integrated MAX399EEE+ Analog Switches & Multiplexers ICs applications.
- Precision data acquisition
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- RGB switches
- Fiber to the Home
- High reliability control systems
- New designs requiring multiplexer functions
- Cellular phones
- Switching Systems
- Automatic test equipment
- Audio and video routing
