MAX399EPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | ALSO OPERATE WITH 3V TO 15V SINGLE SUPPLY |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MAX399 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 20pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 6 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Length | 19.175mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX399EPE Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. Through Hole is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 4:1. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 4 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. It is injected into the electrical part body with 16 pins. A SP4T switching circuit is used for these analog switches. The circuits in this analogue multiplexer number 2. Try searching for the analog switch ic with MAX399 if you are looking for variants. Internally, this switch multiplexer has a resistance of 100Ohm. You can find the functions of the 16 pins in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 15V. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 3V. For this multiplexer to operate, 1μA current would be sufficient. If put voltage greater than 8V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 3V. Operating voltages range from 12V. Don't miss this electronic component's additional features, such as: ALSO OPERATE WITH 3V TO 15V SINGLE SUPPLY.
MAX399EPE Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
Additional Features: ALSO OPERATE WITH 3V TO 15V SINGLE SUPPLY
MAX399EPE Applications
There are a lot of Maxim Integrated MAX399EPE Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- Sample hold systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Audio and video signal routing
- ATM
- Microwave transmission systems
- Communication systems
- High speed data transmission line cards
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- DVD-R
