MAX4038ETA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Number of Pins | 8 |
| Packaging | Strip |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Pin Count | 8 |
| Power Supplies | 3V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.4V |
| Operating Supply Current | 1.9μA |
| Nominal Supply Current | 2.5μA |
| Slew Rate | 0.004 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 50 dB |
| Output Current per Channel | 13mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 4 kHz |
| Gain Bandwidth Product | 4 kHz |
| Unity Gain BW-Nom | 4 kHz |
| Voltage Gain | 108dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Input Bias Current | 1pA |
| Power | NO |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4038ETA+T Overview
An op amp ic of the OPERATIONAL AMPLIFIER type. The op amp is delivered to you in a Strip case. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are attached to buffer op amp. The linear amplifier should be run at 3V at all times, so please keep that in mind when using it. It should be noted that this op amp is a type of Operational Amplifier device. There are 8 pins on this chip. Regarding input offset voltage, op amp rates 200μV. This op amp can operate from a supply current at 1.9μA. 108dB should be the voltage gain. A instrumentation amplifier like this has 1 circuits. As far as the device is concerned, buffer amplifier has 2 channels. The temperature should not be lower than -40°C for operational amplifier ics to operate. No temperature greater than 85°C should be used. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. It is important to keep in mind that the power supply voltage of this electric component is below 3.6V, which is suitable. It is advised to keep the op amp's supply voltage higher than 1.4V.
MAX4038ETA+T Features
8 Pins
supply voltage of 3V
108dB voltage gain
MAX4038ETA+T Applications
There are a lot of Maxim Integrated MAX4038ETA+T Instrumentational OP Amps applications.
- Video amplifiers
- Portable docking station
- Inverse/same-phase proportional circuit
- Differentiator circuits
- Signal transformation
- Radar
- Subtraction operation circuits
- Automotive sensors
- Signal amplification
- Hand-held batteries
