MAX4051ACEE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Base Part Number | MAX4051 |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 250 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Time (Ton, Toff) (Max) | 175ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 6 Ω (Max) |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 1.55mm |
| Length | 4.98mm |
| Width | 3.99mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4051ACEE Overview
Due to its 16-SSOP (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 8:1 represents the number of circuits. Extended operating temperature around 0°C~70°C TA. In total, there have been 16 terminations. By its 8 channels, the electronic component provides high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 16 pins. It consists of 1 circuits. Try searching for the analog switch ic with MAX4051 if you are looking for variants. There is 100Ohm internal resistance in this digital multiplexer. Datasheets for 16 pin functions are available upon request. Users should never supply a voltage higher than 16V to a switch device. The digital multiplexer has a low cost Dual, Single supply. It is recommended that the electrical component receives a voltage of 2V. The analogue multiplexer could operate on 1μA current. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 8V. If you are using dual power supplies, you should attach at least 2.7V. There is a voltage range of 15V operating voltages for the electrical part.
MAX4051ACEE Features
8 Channels
1μA Supply Current
MAX4051ACEE Applications
There are a lot of Maxim Integrated MAX4051ACEE Analog Switches & Multiplexers ICs applications.
- SDH
- Transmit
- DSUs
- SDH/SONET multiplexers
- Battery Powered Instruments
- E1 Network Equipment
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fault Tolerant Systems
- Imaging
- Channelized and Unchannelized DS3 applications
