Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2006 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
3 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4053 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
8V |
Number of Channels |
1 |
Number of Circuits |
3 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
100nA |
Max Supply Current |
100nA |
Number of Bits |
8 |
Turn On Delay Time |
175 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
2V~16V ±2.7V~8V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
2.7V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
2pF 2pF |
On-state Resistance Match-Nom |
6Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
175ns, 150ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
6 Ω (Max) |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Height |
1.55mm |
Length |
4.98mm |
Width |
3.99mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4053ACEE Overview
Due to its 16-SSOP (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tube. This analog switch is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. The operating temperature is extended to around 0°C~70°C TA. 16 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. An electrical component of this type can be found in the 16 series. A SPDT switching circuit is used to build these analog multiplexers. This multiplexer is composed of 3 circuits. Try searching with MAX4053 to find analog multiplexer variants. In this multiplexer, the internal resistance is 100Ohm. The functions of 16 pins can be found in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. A analog switch ic that has a cost-effective Dual, Single supply type. 2V is the lowest voltage the electrical component should receive. This digital switch can be operated with a current of 1μA. Putting voltage greater than 100nA on the multiplexer may cause damage. If put voltage greater than 8V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 2.7V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. It can operate from 8V operating voltages. Its conductivity is 8-bit.
MAX4053ACEE Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
8-Bit
MAX4053ACEE Applications
There are a lot of Maxim Integrated MAX4053ACEE Analog Switches & Multiplexers ICs applications.
- Communication systems
- Digital access cross connects
- Medical systems
- Audio and video switching
- Ultrasound
- T1/E1 Terminals
- Mechanical reed relay replacement
- Sample-and-hold systems
- Automotive applications
- Intelligent PBX