MAX4053AESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4053 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 8V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2V |
| Nominal Supply Current | 100nA |
| Max Supply Current | 100nA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±2.7V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.7V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 6 Ω (Max) |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4053AESE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio between multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. 16 pins are injected to the electronic part body. A SPDT switching circuit is used to build these analog multiplexers. 3 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with MAX4053. This digital multiplexer has 100Ohm internal resistance. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 16V voltage to the switch device. It is recommended to use 2V as the lowest voltage for the electrical part. A voltage higher than 100nA may cause damage to the switch multiplexer. If put voltage greater than 8V on the multiplexer, damage may be caused to the device. If you are using a dual power supply, you should attach at least 2.7V. Operating voltages range from 8V.
MAX4053AESE+T Features
1 Channels
Switch Circuit: SPDT
MAX4053AESE+T Applications
There are a lot of Maxim Integrated MAX4053AESE+T Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Switching Systems
- Digital Cross-Connects
- Optical Applications
- Precision data acquisition
- Audio and video switching
- DSUs
- Audio and video signal routing
- Medical
- Mechanical reed relay replacement
