Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2006 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Terminal Finish |
Tin (Sn) |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
3 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4053 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
8V |
Number of Channels |
1 |
Number of Circuits |
3 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
100nA |
Max Supply Current |
100nA |
Number of Bits |
8 |
Turn On Delay Time |
175 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
2V~16V ±2.7V~8V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
2.7V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
2pF 2pF |
On-state Resistance Match-Nom |
12Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
175ns, 150ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
12 Ω (Max) |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Height Seated (Max) |
1.75mm |
Length |
4.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
MAX4053CEE+ Overview
This electronic part is conveniently packaged in 16-SSOP (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is provided by advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. There is 2:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of 0°C~70°C TA degrees Celsius. 16 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. An electrical component like this is included in the 16 series. Multiplexers built on a SPDT switching circuit are built. There are 3 circuits in this multiplexer. Search with MAX4053 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 100Ohm. The datasheets for the 16 pins explain the functions. A voltage higher than 16V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 2V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 1μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 100nA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 8V. If you are using a dual power supply, you should attach at least 2.7V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. Operating voltages range from 8V. It is able to conduct in a 8-bit way.
MAX4053CEE+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
8-Bit
MAX4053CEE+ Applications
There are a lot of Maxim Integrated MAX4053CEE+ Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Audio/video switches
- USB 1.1 signal switching circuits
- Automotive applications
- Communications systems
- Digital Cross-Connects
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Ultrasound
- Access Concentrators
- 65 V DACs