MAX4053CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4053 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 8V |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100nA |
| Max Supply Current | 100nA |
| Number of Bits | 8 |
| Turn On Delay Time | 175 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 12 Ω (Max) |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 4.572mm |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4053CPE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. Multiplexers and demultiplexers have a ratio of 2:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. In total, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. SPDT switching circuits are used in these analog switch ics. It consists of 3 circuits. Try searching for MAX4053 variants of the analog switch ic. It has an internal resistance of 100Ohm. For functions related to 16 pins, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 16V. Dual, Single supply type digital switch with a low cost. There should be 2V voltage fed to the electrical part below 2V. In order to operate this switch device, it would need a current of 1μA. A digital multiplexer may suffer damage if voltage is applied above 100nA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 8V. A dual power supply should have at least 2.7V voltage attached. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. The electrical part can be operated at 8V voltage levels. It is able to conduct in a 8-bit way.
MAX4053CPE Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
8-Bit
MAX4053CPE Applications
There are a lot of Maxim Integrated MAX4053CPE Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- 65 V DACs
- Battery-powered systems
- CSU
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Video switching
- Precision instrumentation
- Intelligent PBX
- Channelized and Unchannelized DS3 applications
- Industrial
