Parameters |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
3 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4053 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
8V |
Number of Channels |
1 |
Number of Circuits |
3 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
10μA |
Max Supply Current |
1μA |
Number of Bits |
8 |
Turn On Delay Time |
300 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
2V~16V ±2.7V~8V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
600 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
2.7V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
2pF 2pF |
On-state Resistance Match-Nom |
12Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
175ns, 150ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
12 Ω (Max) |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
175ns |
Switch-off Time-Max |
150ns |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2006 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Max Power Dissipation |
696mW |
Technology |
CMOS |
MAX4053CSE Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tube is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature around 0°C~70°C TA extended. Total terminations are 16. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 16 series. SPDT switching circuits are used in these analog switch ics. 3 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with MAX4053. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. For details about the functions of 16 pins, please refer to the datasheets. normally, users should not supply switches with voltages higher than 16V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 2V is the lowest voltage the electrical component should receive. 1μA current would be enough for this multiplexer to operate. When the digital multiplexer is charged above 1μA, damage can occur. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 8V. It is recommended that you attach at least 2.7V to your dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating voltages range from 8V. The switch device is capable of conducting in a 8-bit mode.
MAX4053CSE Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
8-Bit
MAX4053CSE Applications
There are a lot of Maxim Integrated MAX4053CSE Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Switching Systems
- Frame Relay Equipment
- Battery Powered Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Industrial and process control systems
- High-Voltage
- Multi-Line E1 Interface Cards
- Communication systems
- Audio and video switching