MAX4053CSE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4053 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 8V |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100nA |
| Max Supply Current | 100nA |
| Turn On Delay Time | 175 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 12 Ω (Max) |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4053CSE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature around 0°C~70°C TA extended. 16 terminations have been made so far. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. The electronic part body is injected with 16 pins. Based on SPDT switching circuits, these analog multiplexers work. The circuits in this analogue multiplexer number 3. Try searching for the analog switch ic with MAX4053 if you are looking for variants. A 100Ohm internal resistance characterizes this multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. Users should never supply a voltage higher than 16V to a switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 2V voltage fed to the electrical part below 2V. 1μA current would be enough for this multiplexer to operate. A digital multiplexer may suffer damage if voltage is applied above 100nA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 8V. When using dual power supplies, you should attach at least 2.7V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. It can operate from 8V operating voltages.
MAX4053CSE+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4053CSE+T Applications
There are a lot of Maxim Integrated MAX4053CSE+T Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- Medical Instrumentation
- Communications systems
- Avionics
- Imaging
- Fiber to the Home
- Power routing
- RGB switches
- Multiplexers
- Cross Connects
