MAX4053EEE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4053 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 8V |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100nA |
| Max Supply Current | 100nA |
| Turn On Delay Time | 175 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 12 Ω (Max) |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 1.55mm |
| Length | 4.98mm |
| Width | 3.99mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX4053EEE+ Overview
Shipping overseas is convenient with the electronic component packed in 16-SSOP (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tube is used. In Surface Mount, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 2:1. Extended operating temperature around -40°C~85°C TA. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 1 channels. Turning on and running the electrical part should be easy with a 5V voltage supply. Electronic part bodies are injected with 16 pins. Based on SPDT switching circuits, these analog multiplexers work. This multiplexer is composed of 3 circuits. Try searching with MAX4053 to find analog multiplexer variants. Analog switches have 100Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. normally, users should not supply switches with voltages higher than 16V. Digital switch that provides Dual, Single power at a cost-effective price. There should be 2V voltage fed to the electrical part below 2V. In order to operate this switch device, it would need a current of 1μA. Put voltage above 100nA on the multiplexer to cause damage. If put voltage greater than 8V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 2.7V voltage attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating voltages range from 8V.
MAX4053EEE+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4053EEE+ Applications
There are a lot of Maxim Integrated MAX4053EEE+ Analog Switches & Multiplexers ICs applications.
- Automotive applications
- Remote Powered Equipment
- High reliability control systems
- Avionics
- Cell phones
- Audio signal routing
- Mechanical reed relay replacement
- Industrial and process control systems
- Data Acquisition Systems
- Automatic test equipment
