MAX4053EPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX4053 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±2.7V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| On-State Resistance (Max) | 100Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 12Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 12 Ω (Max) |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Switch-off Time-Max | 150ns |
| Height Seated (Max) | 4.572mm |
| Length | 19.175mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
MAX4053EPE+ Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tube. This analog switch is mounted in Through Hole. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. There are 16 terminations totally. High-quality output is provided by the electronic component's 1 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 16 series. SPDT switching circuits are used in these analog switch ics. The multiplexer consists of 3 circuits. Try searching with MAX4053 if you're looking for variants. For functions related to 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX4053EPE+ Features
1 Channels
Switch Circuit: SPDT
MAX4053EPE+ Applications
There are a lot of Maxim Integrated MAX4053EPE+ Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- SDH/SONET multiplexers
- Medical Instrumentation
- Battery Powered Systems
- Wireless Local Loop
- Isolation
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Power routing
- USB 1.1 signal switching circuits
