Parameters |
Packaging |
Tube |
Published |
2006 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
3 |
Supply Voltage |
5V |
Terminal Pitch |
2.54mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4053 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
8V |
Number of Channels |
1 |
Number of Circuits |
3 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
100nA |
Max Supply Current |
100nA |
Number of Bits |
8 |
Turn On Delay Time |
175 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
2V~16V ±2.7V~8V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
2.7V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
2pF 2pF |
On-state Resistance Match-Nom |
12Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
175ns, 150ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
12 Ω (Max) |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Height Seated (Max) |
4.572mm |
Length |
19.175mm |
Width |
7.62mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
MAX4053EPE Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tube. There is an analog multiplexer mounted in position Through Hole. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -40°C~85°C TA. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. There is an electrical component included in the 16 series. On the other hand, analog switches can be constructed using SPDT switching circuits. There are 3 circuits in this switch device. Look for analog switch ic variants by searching with MAX4053. This digital multiplexer has 100Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 16V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. For this multiplexer to operate, 1μA current would be sufficient. Putting voltage greater than 100nA on the multiplexer may cause damage. Despite this switch's dual supply capability, its voltage should not exceed 8V. With dual power supplies, you should attach at least 2.7V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. This electrical part is compatible with 8V operating voltages. 8-bit conductivity is possible.
MAX4053EPE Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
8-Bit
MAX4053EPE Applications
There are a lot of Maxim Integrated MAX4053EPE Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Audio signal routing
- Video switching
- High speed data transmission line cards
- Precision instrumentation
- SDH
- Communications systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- DVD-R
- Avionics