Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1996 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
45Ohm |
Terminal Finish |
Tin (Sn) |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
0.635mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4066 |
Pin Count |
16 |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
150 ns |
Supply Type |
Single |
Turn-Off Delay Time |
185 ns |
-3db Bandwidth |
100MHz |
On-State Resistance (Max) |
45Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
0.3Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
100ns, 75ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-86dB @ 1MHz |
Switch-on Time-Max |
125ns |
Switch-off Time-Max |
75ns |
Voltage - Supply, Single (V+) |
2V~16V |
Height Seated (Max) |
1.75mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4066AEEE+ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SSOP (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. There are 16 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. The analog switch ics are built using SPST - NO switching circuits. The multiplexer consists of 4 circuits. If you are looking for variants of the digital switch, trying search with MAX4066. It has an internal resistance of 45Ohm. You can find the functions of the 16 pins in the datasheets. It is generally not recommended to supply a voltage higher than 16V to the switch device in normal circumstances. The analog switch ic is of the Single supply type and is cost-effective. A low voltage of 2V should be applied to the electronic component. An operating current of 1μA would be sufficient for this switch device. This analogue multiplexer requires a voltage of 2V~16V when it drains from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer.
MAX4066AEEE+ Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 100MHz
MAX4066AEEE+ Applications
There are a lot of Maxim Integrated MAX4066AEEE+ Analog Switches & Multiplexers ICs applications.
- Imaging
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Data switching
- Digital cross connects (DSX-1)
- DSUs
- Cross Connects
- Audio and video switching
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Audio/video switches
- PDAs