MAX4066AEPD
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 45Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -86dB @ 1MHz |
| Switch-on Time-Max | 125ns |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2V~16V |
| Normal Position | NO |
| Length | 19.05mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4066AEPD Overview
Shipping overseas is convenient with the electronic component packed in 14-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. Mounted in Through Hole is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. Totally, there are 14 terminations. The electronic part provides high-quality output because it has 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 14 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. The circuits in this analogue multiplexer number 4. Try searching for the analog switch ic with MAX4066 if you are looking for variants. An switch multiplexer with 45Ohm internal resistance has a value of 45Ohm. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 16V voltage to the switch device. Analog switch ics with Single supply type are cost-effective. 2V is the lowest voltage the electrical component should receive. For this digital switch to work, 1μA current would suffice. An analogue multiplexer drains from a single voltage supply at 2V~16V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX4066AEPD Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 100MHz
MAX4066AEPD Applications
There are a lot of Maxim Integrated MAX4066AEPD Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Avionics and Military Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cell phones
- Automatic test equipment
- Channel Banks
- Avionics
- Battery Powered Systems
- T1/E1 Terminals
- PCMCIA cards
