MAX4066CPD+
| Parameters | |
|---|---|
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 45Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -86dB @ 1MHz |
| Switch-on Time-Max | 125ns |
| Voltage - Supply, Single (V+) | 2V~16V |
| Length | 19.05mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | MAX4066 |
| Pin Count | 14 |
| Number of Channels | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1nA |
| Throw Configuration | SPST |
MAX4066CPD+ Overview
Packed in 14-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to 0°C~70°C TA. In total, there have been 14 terminations. High-quality output is provided by the electronic component's 4 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. An electrical component of this type can be found in the 14 series. The analog switch ics are built using SPST - NO switching circuits. MAX4066 can be used to search for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 45Ohm. To find out what the functions of 14 pins are, please refer to their datasheets. In normalcircumstances, users should not exceed 16V volts for the multiplexer. An effective Single supply digital multiplexer. There should be 2V voltage fed to the electrical part below 2V. For this digital switch to work, 1μA current would suffice. Analogue multiplexers require a 2V~16V voltage to drain from a single voltage supply. If you put voltage higher than 1nA on the digital multiplexer, damage may occur.
MAX4066CPD+ Features
4 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 100MHz
MAX4066CPD+ Applications
There are a lot of Maxim Integrated MAX4066CPD+ Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Private Branch Exchange (PBX)
- Signal routing between systems
- Transmit
- SONET
- Ultrasound
- High reliability control systems
- Relay Replacement
- HDTV
- Battery Powered Systems
