MAX4066CSD
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Polarity | Non-Inverting |
| Number of Channels | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 45Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -86dB @ 1MHz |
| Switch-on Time-Max | 125ns |
| Voltage - Supply, Single (V+) | 2V~16V |
| Normal Position | NO |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4066CSD Overview
Shipping overseas is convenient with the electronic component packed in 14-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tube. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature around 0°C~70°C TA extended. There are 14 terminations totally. This electronic part offers high-quality output due to its 4 channels. An 5V voltage supply should allow the electrical part to be turned on and run. An injection of 14 pins is performed into the body of the electrical component. SPST - NO switching circuits are used in these analog switch ics. Use MAX4066 to search for variants of the digital switches. A 45Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 14 pins are available. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. The analog switch ic is of the Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 2V. The analogue multiplexer could operate on 1μA current. Draining from a single voltage supply, this analog switch requires a voltage of 2V~16V. Put voltage above 1nA on the multiplexer to cause damage. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX4066CSD Features
4 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 100MHz
MAX4066CSD Applications
There are a lot of Maxim Integrated MAX4066CSD Analog Switches & Multiplexers ICs applications.
- ATM
- New designs requiring multiplexer functions
- Multi-Line E1 Interface Cards
- FTTH
- DSUs
- Remote Powered Equipment
- Automatic test equipment
- Data switching
- Audio/video switches
- MP3 players
