MAX406AEPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX406 |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Current - Supply | 1μA |
| Slew Rate | 0.005V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 0.1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~10V |
| Gain Bandwidth Product | 8kHz |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Unity Gain BW-Nom | 40 kHz |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Low-Offset | NO |
| Frequency Compensation | YES AVCL>=2 |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 750μV |
| Current - Output / Channel | 600μA |
| Low-Bias | YES |
| Micropower | YES |
| Neg Supply Voltage-Max (Vsup) | -6V |
| Voltage Gain-Min | 200000 |
| Common-mode Reject Ratio-Min | 70 dB |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| RoHS Status | ROHS3 Compliant |
MAX406AEPA+ Overview
Packaging for the buffer amplifier is in the form of a 8-DIP (0.300, 7.62mm) case. Buffer amps of this type are called General Purpose-types. In the case of Tube cases, linear amplifier will be delivered. During the past two weeks, there have been close to 8 terminations. Buffer amplifier has a total of 8 pins on it. The linear amplifier should be run at 2.5V at all times, so please keep that in mind when using it. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. This electronic part is recommended for mounting type Through Hole. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . A linear amplifier like this has 1 circuits on it. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. In order to ensure optimal performance, an 1μA supply is recommended for this electrical component. It is necessary to keep in mind that this instrumentation amplifier is able to conduct a minimum voltage gain of 200000.
MAX406AEPA+ Features
8 Pins
supply voltage of 2.5V
Output Type: Rail-to-Rail
MAX406AEPA+ Applications
There are a lot of Maxim Integrated MAX406AEPA+ Instrumentational OP Amps applications.
- Portable electronic products powered by batteries
- Information processing
- Video conversion and routing
- Semiconductor detectors
- High-frequency data acquisition systems
- Division circuits
- Multiplication circuits
- Signal operation
- Computer workstations
- Hand-held batteries
