MAX407ESA+T
| Parameters | |
|---|---|
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX407 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 2 |
| Current - Supply | 1μA |
| Slew Rate | 0.005V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 0.1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~10V |
| Bandwidth | 8 kHz |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Unity Gain BW-Nom | 8 kHz |
| Average Bias Current-Max (IIB) | 0.00005μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 10V |
| Voltage - Input Offset | 1mV |
| Current - Output / Channel | 600μA |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Voltage Gain-Min | 100000 |
| Common-mode Reject Ratio-Min | 60 dB |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
MAX407ESA+T Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. There are two types of operational amplifiers in this circuit. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 2.5V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. Surface Mount is the recommended mounting type for this linear amplifier. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. There are 2 circuits on op amps. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. It is recommended that you use an 1μA power supply with this electrical part in order for it to operate correctly. There is a minimum voltage gain of 100000 that this buffer op amp is capable of conducting.
MAX407ESA+T Features
8 Pins
supply voltage of 2.5V
Output Type: Rail-to-Rail
MAX407ESA+T Applications
There are a lot of Maxim Integrated MAX407ESA+T Instrumentational OP Amps applications.
- Comparator
- Medical imaging
- RF cable systems
- Multimedia playback equipment
- ECG equipment
- Active probe
- E-book readers
- PDA
- Automatic control
- Communication
