Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
0°C~70°C |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Operational Amplifier |
Packing Method |
TAPE AND REEL |
Max Power Dissipation |
471mW |
Technology |
BIPOLAR |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX412 |
Pin Count |
8 |
JESD-30 Code |
R-PDSO-G8 |
Operating Supply Voltage |
9V |
Number of Circuits |
2 |
Operating Supply Current |
2.5mA |
Nominal Supply Current |
5.4mA |
Slew Rate |
4.5V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
115 dB |
Current - Input Bias |
80nA |
Voltage - Supply, Single/Dual (±) |
4.8V~10.5V ±2.4V~5.25V |
Output Current per Channel |
35mA |
Supply Type |
Dual, Single |
Input Offset Voltage (Vos) |
120μV |
Gain Bandwidth Product |
28MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Unity Gain BW-Nom |
28000 kHz |
Voltage Gain |
122dB |
Power Supply Rejection Ratio (PSRR) |
96dB |
Low-Offset |
YES |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
6V |
Bias Current-Max (IIB) @25C |
0.15μA |
Dual Supply Voltage |
5V |
Height Seated (Max) |
1.75mm |
Length |
4.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX412BCSA+T Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. General Purpose-type instrumentation amplifiers are used in this application. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. There have been a total of 8 terminations over the past year. A total of 8 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 5V volts. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. Op amp rates 120μV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . You can run this op amp ic on 2.5mA . The voltage gain should stay at 122dB. In total, there are 2 circuits on this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 9V. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.
MAX412BCSA+T Features
8 Pins
supply voltage of 5V
122dB voltage gain
MAX412BCSA+T Applications
There are a lot of Maxim Integrated MAX412BCSA+T Instrumentational OP Amps applications.
- Signal transformation
- Proportional operation circuits
- Portable electronic products powered by batteries
- Test equipment
- Displayers for aircraft and air transportation control systems
- E-book readers
- Signal amplification
- Fission chambers
- Fast A/D and D/A converters
- Thermocouples