MAX4165EUK-T
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 571mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4165 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3.25V |
| Number of Channels | 1 |
| Operating Supply Current | 1.3mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 125mA |
| Slew Rate | 2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 63 dB |
| Current - Input Bias | 50nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6.5V ±1.35V~3.25V |
| Output Current per Channel | 125mA |
| Input Offset Voltage (Vos) | 350μV |
| Bandwidth | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 120dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Dual Supply Voltage | 3V |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4165EUK-T Overview
There is a SC-74A, SOT-753 case in which the instrumentation amplifier is packaged. The instrumentation amplifier in this picture is of the General Purpose-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. It is estimated that there will be 5 terminations in the next few months. In this case, there are 5 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 5 pins are available on the instrumentation amplifier. Regarding input offset voltage, op amp rates 350μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. This op amp can operate from a supply current at 1.3mA. 120dB should be the voltage gain. There are a total of 1 channels available on the op amps. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 3.25V voltage. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
MAX4165EUK-T Features
5 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
MAX4165EUK-T Applications
There are a lot of Maxim Integrated MAX4165EUK-T Instrumentational OP Amps applications.
- Communication
- Fast A/D and D/A converters
- Multimedia playback equipment
- Industrial control system
- Precision measurement
- Comparator
- Band-stop filter
- Inverse/same-phase proportional circuit
- Ultrasound transducers
- PDA
