MAX4166EPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Package / Case | DIP |
| Number of Pins | 8 |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifiers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Pin Count | 8 |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 6.5V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1.3mA |
| Slew Rate | 2 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 72 dB |
| Output Current per Channel | 125mA |
| Input Offset Voltage (Vos) | 250μV |
| Gain Bandwidth Product | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.225μA |
| Power Supply Rejection Ratio (PSRR) | 72dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 3.25V |
| Min Dual Supply Voltage | 1.35V |
| Input Bias Current | 50nA |
| Input Voltage Noise Density | 26nV/sqrt Hz |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4166EPA+ Overview
Packaged in a DIP case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. The number of terminations is approaching the 8 mark. In total, there are 8 pins on this op amp ic. Please take in mind that op amp should be run at 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiersed as a Operational Amplifiers-type device. The op amp ic has an array of 8 pins on it. In terms of the input offset voltage, instrumentation amplifier rates at 250μV. The buffer amplifier is capable of operating from a supply current of 1.3mA . Maintain 120dB as the voltage gain. Op amp ic has 1 channels. This instrumentation amplifier cannot operate below -40°C degrees Celsius. No temperature greater than 85°C should be used. With regard tp supply voltage, op amp is used under 6.5V. As a rule of thumb, the supply voltage of the op amp should not be lower than 2.7V. It is recommended that you conduct this electronic part using the dual supply voltage of 3.25V.
MAX4166EPA+ Features
8 Pins
supply voltage of 5V
120dB voltage gain
MAX4166EPA+ Applications
There are a lot of Maxim Integrated MAX4166EPA+ Instrumentational OP Amps applications.
- Television
- Fast A/D and D/A converters
- RF cable systems
- High input resistance broadband
- Navigation
- Signal transformation
- Information processing
- Power transmission
- Instrumentation
- Differentiator circuits
