MAX4173HESA-T
| Parameters | |
|---|---|
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Base Part Number | MAX4173 |
| Pin Count | 8 |
| Output Type | Voltage |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Operating Supply Current | 420μA |
| Nominal Supply Current | 420μA |
| Adjustable Threshold | NO |
| Accuracy | 0.5 % |
| Amplifier Type | Current Sense |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 700μA |
| Voltage - Supply, Single/Dual (±) | 3V~28V |
| Input Offset Voltage (Vos) | 300μV |
| Voltage Gain | 100dB |
| Power Supply Rejection Ratio (PSRR) | 60dB |
| -3db Bandwidth | 1.2MHz |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Other Analog ICs |
| Max Power Dissipation | 471mW |
MAX4173HESA-T Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. The instrumentation amplifier in this picture is of the Current Sense-type. Linear amplifier is delivered in a Tape & Reel (TR) case. The number of terminations is approaching the 8 mark. The pins on this board total to 8 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 12V. To be specific, this instrumentation amplifier is a type of Other Analog ICs. 8 pins are available on the instrumentation amplifier. There is an input offset voltage of 300μV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Operational amplifier can operate supply current at 420μA. Voltage gain should remain at 100dB. There are 1 circuits on op amps. 1 channels are available on the instrumentation amplifier. In addition to outputting Voltage signals, this op amp ic offers a number of other advantages. An analog IC known as POWER SUPPLY SUPPORT CIRCUIT is also used in this linear amplifier.
MAX4173HESA-T Features
8 Pins
supply voltage of 12V
100dB voltage gain
Output Type: Voltage
MAX4173HESA-T Applications
There are a lot of Maxim Integrated MAX4173HESA-T Instrumentational OP Amps applications.
- Division circuits
- Automation control systems
- High gain DC amplifier
- High speed sample
- Non-polarized electrodes
- MP3
- High/low-pass filter circuit
- Switching amplifier
- Laptop
- Radar
