MAX4233AUB+T
| Parameters | |
|---|---|
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4233 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Circuits | 2 |
| Operating Supply Current | 1.2mA |
| Nominal Supply Current | 1.1mA |
| Output Current | 200mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 52 dB |
| Current - Input Bias | 50pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 200mA |
| Input Offset Voltage (Vos) | 850μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.00055μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Power | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C |
MAX4233AUB+T Overview
It is packaged in an 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. Op amps are General Purpose types of amplifier on the chip. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. It is estimated that there will be 10 terminations in the next few months. The total number of pins on linear amplifier is 10. Please take in mind that op amp should be run at 2.7V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. There are 10 pins on this chip. There is an input offset voltage of 850μV for this buffer op amp. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. As long as the supply current of the chip does not exceed 1.2mA, this op amp ic can operate. It is a member of the 100dB's 100dB family. During the manufacturing process, this buffer amplifier is divided into 2 circuits. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The linear amplifier is packaged by using a TAPE AND REEL axis.
MAX4233AUB+T Features
10 Pins
supply voltage of 2.7V
100dB voltage gain
Output Type: Rail-to-Rail
MAX4233AUB+T Applications
There are a lot of Maxim Integrated MAX4233AUB+T Instrumentational OP Amps applications.
- Fast A/D and D/A converters
- Precision measurement
- Wireless base stations
- Logarithmic operation circuits
- ECG equipment
- Large motor controllers
- Communication
- Signal operation
- Signal filtering
- Voltage regulation circuit
