MAX4236AESA+
| Parameters | |
|---|---|
| Programmable Power | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifiers |
| Max Power Dissipation | 471mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4236 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 350μA |
| Nominal Supply Current | 350μA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 84 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~5.5V ±1.2V~2.75V |
| Output Current per Channel | 30mA |
| Supply Type | Single |
| Input Offset Voltage (Vos) | 5μV |
| Bandwidth | 1.7MHz |
| Unity Gain BW-Nom | 7500 kHz |
| Voltage Gain | 128dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Power Supply Rejection Ratio (PSRR) | 97dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | YES |
MAX4236AESA+ Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tube case. A total of 8 terminations have been reported in the past few weeks. There are a total of 8 pins on this op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifiers devices. It has 8 pins that make up the linear amplifier. There is an input offset voltage of 5μV for this buffer op amp. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, op amp ranges -40°C~85°C. In order for this instrumentation amplifier to operate, the supply current needs to be between 350μA and 10 . It is recommended to keep the voltage gain at 128dB at all times. On the buffer amps, there are 1 channels that can be used. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of instrumentation amplifier is rated 5V voltage.
MAX4236AESA+ Features
8 Pins
supply voltage of 5V
128dB voltage gain
Output Type: Rail-to-Rail
MAX4236AESA+ Applications
There are a lot of Maxim Integrated MAX4236AESA+ Instrumentational OP Amps applications.
- ECG equipment
- Instrumentation
- earphone
- Test equipment
- Subtraction operation circuits
- Signal filtering
- Non-polarized electrodes
- Large motor controllers
- Differentiator circuits
- Television broadcasting equipment
