MAX4236BESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifiers |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 471mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4236 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Circuits | 1 |
| Operating Supply Current | 350μA |
| Supply Current-Max | 0.44mA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 84 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~5.5V ±1.2V~2.75V |
| Output Current per Channel | 30mA |
| Supply Type | Single |
| Input Offset Voltage (Vos) | 5μV |
| Bandwidth | 1.7MHz |
| Unity Gain BW-Nom | 7500 kHz |
| Voltage Gain | 128dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Power Supply Rejection Ratio (PSRR) | 97dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4236BESA+T Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. An op amp of this type is a General Purpose-type. A Tape & Reel (TR) case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 5V volts. There are two types of Operational Amplifiers op amps in this case, and this device falls into one of them. As far as the input offset voltage is concerned, linear amplifier rates at 5μV. For this electrical component, Surface Mount is the recommended mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureThe buffer amplifier is capable of operating from a supply current of 350μA . 128dB should remain the voltage gain. There are 1 circuits on op amps. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The operating supply voltage of the buffer op amp is rated at 5V. The linear amplifier is packaged by using a TAPE AND REEL axis.
MAX4236BESA+T Features
8 Pins
supply voltage of 5V
128dB voltage gain
Output Type: Rail-to-Rail
MAX4236BESA+T Applications
There are a lot of Maxim Integrated MAX4236BESA+T Instrumentational OP Amps applications.
- Band-pass filter
- Communication device
- RF cable systems
- Medical instruments
- Laptop
- Fast A/D and D/A converters
- Image computer boards
- Test and measurement instruments
- Communication
- Comparator
