MAX4236EUT+T
| Parameters | |
|---|---|
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 5μV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Power | NO |
| Length | 2.9mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifiers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4236 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Circuits | 1 |
| Current - Supply | 350μA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 102 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~5.5V ±1.2V~2.75V |
| Bandwidth | 1.7MHz |
| Unity Gain BW-Nom | 7500 kHz |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
MAX4236EUT+T Overview
There is a SOT-23-6 case in which the instrumentation amplifier is packaged. An op amp of this type is a General Purpose-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. The number of terminations is approaching the 6 mark. A total of 6 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. A type of Operational Amplifiers op amp ic can be identified by the fact that this is a type of Operational Amplifiers device. It has 6 pins that make up the linear amplifier. The mounting type that is recommended for this electrical part is Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. On this buffer amplifier, there are 1 circuits. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. There is a recommendation that this electrical part be used with a supply with 350μA current rating.
MAX4236EUT+T Features
6 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
MAX4236EUT+T Applications
There are a lot of Maxim Integrated MAX4236EUT+T Instrumentational OP Amps applications.
- Tablets
- Ultrasound transducers
- Division circuits
- Weak signal detection
- High/low-pass filter circuit
- Test and measurement instruments
- Precision measurement
- Portable electronic products powered by batteries
- Oscilloscopes
- Active probe
