MAX4237EUT+T
| Parameters | |
|---|---|
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Weight | 36.003894mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 696mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4237 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 350μA |
| Supply Current-Max | 0.44mA |
| Slew Rate | 1.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 82 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~5.5V ±1.2V~2.75V |
| Output Current per Channel | 30mA |
| Supply Type | Single |
| Input Offset Voltage (Vos) | 5μV |
| Bandwidth | 7.5MHz |
| Unity Gain BW-Nom | 7500 kHz |
| Voltage Gain | 128dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Power Supply Rejection Ratio (PSRR) | 97dB |
| Low-Offset | YES |
| Frequency Compensation | YES AVCL>=5 |
| Supply Voltage Limit-Max | 6V |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 1.1mm |
| Length | 2.9mm |
| Width | 1.63mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
MAX4237EUT+T Overview
A SOT-23-6 case is used to package the op amp. An op amp of this type is a General Purpose-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. It is estimated that there will be 6 terminations in the next few months. Buffer amplifier has a total of 6 pins. It is important to remember that this op amp should be operated at a voltage of 5V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. In total, the buffer amplifier consists of 6 pins. Regarding input offset voltage, op amp rates 5μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . It is possible to operate this buffer amplifier from a supply current of 350μA . 128dB should remain the voltage gain. There are a total of 1 channels available on the op amps. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 5V.
MAX4237EUT+T Features
6 Pins
supply voltage of 5V
128dB voltage gain
Output Type: Rail-to-Rail
MAX4237EUT+T Applications
There are a lot of Maxim Integrated MAX4237EUT+T Instrumentational OP Amps applications.
- Precision measurement
- Home audio systems
- Weighing systems
- High-frequency data acquisition systems
- Large motor controllers
- Test and measurement instruments
- Strain gauges
- Hand-held batteries
- Multiplication circuits
- E-book readers
