MAX4238ATT+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-WDFN Exposed Pad |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 471mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4238 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Circuits | 1 |
| Operating Supply Current | 600μA |
| Supply Current-Max | 0.9mA |
| Slew Rate | 0.35V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 120 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 100nV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 150dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 0.1μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height Seated (Max) | 0.8mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4238ATT+T Overview
In the package, you will find a 6-WDFN Exposed Pad-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. A total of 6 terminations have been reported in the past few weeks. A total of 6 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 5V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. A total of 6 pins are present on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 100nV. Surface Mount is the recommended mounting type for this linear amplifier. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . Operational amplifier can operate supply current at 600μA. 150dB should be the voltage gain. This op amp ic has 1 circuits. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. This linear amplifier pack is based on the TAPE AND REEL axis.
MAX4238ATT+T Features
6 Pins
supply voltage of 5V
150dB voltage gain
Output Type: Rail-to-Rail
MAX4238ATT+T Applications
There are a lot of Maxim Integrated MAX4238ATT+T Instrumentational OP Amps applications.
- Navigation
- Car stereo
- Information processing
- Portable docking station
- Exponential operation circuits
- Video amplifiers
- Signal amplification
- High/low-pass filter circuit
- Video computer boards
- Precision measurement
