MAX4245AUT+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4245 |
| Pin Count | 6 |
| JESD-30 Code | R-PDSO-G6 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Current - Supply | 375μA |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 10nA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V ±1.25V~2.75V |
| Gain Bandwidth Product | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 400μV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.05μA |
| Programmable Power | NO |
| Wideband | NO |
| Power | NO |
| Length | 2.9mm |
| RoHS Status | ROHS3 Compliant |
MAX4245AUT+T Overview
In the package, you will find a SOT-23-6-case to contain the op amp ic. Buffer amps of this type are called General Purpose-types. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. During the past two weeks, there have been close to 6 terminations. The pins on this board total to 6 in total. I would like to remind you that this buffer op amp should be powered by an 2.7V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. For this electrical component, Surface Mount is the recommended mounting type. With regard to operating temperature, this op amp functions well at -40°C~125°C. There are 1 circuits on op amps. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. We recommend that you use this electronic part with an 375μA supply in order to get the best performance from it.
MAX4245AUT+T Features
6 Pins
supply voltage of 2.7V
Output Type: Rail-to-Rail
MAX4245AUT+T Applications
There are a lot of Maxim Integrated MAX4245AUT+T Instrumentational OP Amps applications.
- Fission chambers
- Displayers for aircraft and air transportation control systems
- Laptop
- Test and measurement instruments
- Professional videography
- Car stereo
- Comparator
- Power control
- High/low-pass filter circuit
- Navigation
