MAX4250AAUK+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOT-23 |
| Number of Pins | 5 |
| Packaging | Strip |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Pin Count | 5 |
| Operating Supply Voltage | 2.75V |
| Power Supplies | 5V |
| Temperature Grade | AUTOMOTIVE |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.4V |
| Operating Supply Current | 420μA |
| Nominal Supply Current | 400μA |
| Output Current | 68mA |
| Slew Rate | 0.3 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 68 dB |
| Output Current per Channel | 68mA |
| Input Offset Voltage (Vos) | 70μV |
| Gain Bandwidth Product | 3MHz |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 77dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 2.75V |
| Low-Bias | NO |
| Micropower | YES |
| Min Dual Supply Voltage | 1.2V |
| Programmable Power | NO |
| Input Bias Current | 1pA |
| Wideband | NO |
| Power | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4250AAUK+T Overview
The linear amplifier is packaged in a SOT-23 case. Buffer amps of this type are called OPERATIONAL AMPLIFIER-types. A Strip case is used for delivering the op amp. The number of terminations approaches 5. In this case, there are 5 pins on the board. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. Instrumentation amplifier is a part of Operational Amplifier. In total, the buffer amplifier consists of 5 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 70μV. In order for this instrumentation amplifier to operate, the supply current needs to be between 420μA and 10 . The voltage gain should stay at 77dB. Buffer op amp is equipped with 1 channels on the device. In order for this buffer op amp to function, it should have a temperature of at least -40°C degrees Celsius. In order to avoid damage to the product, instrumentation amplifier should only be used at temperatures below 125°C. The operating supply voltage of instrumentation amplifier is rated 2.75V voltage. The linear amplifier is packaged by using a TAPE AND REEL axis. Under 5.5V is the minimum supply voltage for this electric component. As a rule of thumb, the supply voltage of the op amp should not be lower than 2.4V. It is recommended that you conduct this electronic part using the dual supply voltage of 2.75V.
MAX4250AAUK+T Features
5 Pins
supply voltage of 5V
77dB voltage gain
MAX4250AAUK+T Applications
There are a lot of Maxim Integrated MAX4250AAUK+T Instrumentational OP Amps applications.
- Polarized electrodes
- Cinema or auditorium audio system
- Logarithmic operation circuits
- Navigation
- Weighing systems
- Band-stop filter
- Test equipment
- Tablets
- Communication
- Inverse/same-phase proportional circuit
