Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C |
Packaging |
Tape & Reel (TR) |
Published |
2012 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Subcategory |
Operational Amplifier |
Packing Method |
TAPE AND REEL |
Technology |
BICMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
245 |
Number of Functions |
1 |
Supply Voltage |
5V |
Base Part Number |
MAX4251 |
Pin Count |
8 |
Output Type |
Push-Pull, Rail-to-Rail |
Operating Supply Voltage |
2.75V |
Power Supplies |
5V |
Number of Circuits |
1 |
Operating Supply Current |
420μA |
Nominal Supply Current |
400μA |
Output Current |
68mA |
Slew Rate |
0.3V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
70 dB |
Current - Input Bias |
1pA |
Voltage - Supply, Single/Dual (±) |
2.4V~5.5V ±1.2V~2.75V |
Output Current per Channel |
68mA |
Input Offset Voltage (Vos) |
70μV |
Gain Bandwidth Product |
3MHz |
Unity Gain BW-Nom |
3000 kHz |
Voltage Gain |
116dB |
Low-Offset |
YES |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
6V |
Low-Bias |
YES |
Micropower |
YES |
Programmable Power |
NO |
Wideband |
NO |
Power |
NO |
Length |
4.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4251ESA-T Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. This is a General Purpose type op amp. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are attached to buffer op amp. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The op amp ic has an array of 8 pins on it. Op amp ic rates 70μV for input offset voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. It is possible to operate this buffer amplifier from a supply current of 420μA . Voltage gain should remain at 116dB. This op amp ic has 1 circuits. A benefit of this op amp ic is that it outputs Push-Pull, Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of the buffer op amp is rated at 2.75V. This linear amplifier pack is based on the TAPE AND REEL axis.
MAX4251ESA-T Features
8 Pins
supply voltage of 5V
116dB voltage gain
Output Type: Push-Pull, Rail-to-Rail
MAX4251ESA-T Applications
There are a lot of Maxim Integrated MAX4251ESA-T Instrumentational OP Amps applications.
- Test and measurement instruments
- Differentiator circuits
- Division circuits
- Integrator circuits
- E-book readers
- Mobile phone
- ECG equipment
- Medical instruments
- Fast A/D and D/A converters
- Industrial applications including automation