MAX4252EUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 362mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4252 |
| Pin Count | 8 |
| Output Type | Push-Pull, Rail-to-Rail |
| Operating Supply Voltage | 2.75V |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Operating Supply Current | 420μA |
| Nominal Supply Current | 400μA |
| Output Current | 68mA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~5.5V ±1.2V~2.75V |
| Output Current per Channel | 68mA |
| Input Offset Voltage (Vos) | 70μV |
| Bandwidth | 3MHz |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 116dB |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4252EUA+T Overview
Packaging for the buffer amplifier is in the form of a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. An op amp of this type is a General Purpose-type. Linear amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. An 8-pin op amp ic is included in the package. As far as the input offset voltage is concerned, linear amplifier rates at 70μV. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . The buffer amplifier is capable of operating from a supply current of 420μA . 116dB should remain the voltage gain. This op amp contains 2 circuits. On the output type, there are Push-Pull, Rail-to-Rail different types of op amps. The operating supply voltage of instrumentation amplifier is rated 2.75V voltage. An buffer amplifier is packed in a TAPE AND REEL-shape according to the design.
MAX4252EUA+T Features
8 Pins
supply voltage of 5V
116dB voltage gain
Output Type: Push-Pull, Rail-to-Rail
MAX4252EUA+T Applications
There are a lot of Maxim Integrated MAX4252EUA+T Instrumentational OP Amps applications.
- RF cable systems
- Automation control systems
- Power control
- Multiplication circuits
- Gaming industry
- Vehicle electronics
- Cinema or auditorium audio system
- Mobile phone
- Laptop
- Signal amplification
