MAX4253EBC+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 12-WFBGA, CSPBGA |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4253 |
| Pin Count | 10 |
| JESD-30 Code | R-PBGA-B10 |
| Qualification Status | Not Qualified |
| Output Type | Push-Pull, Rail-to-Rail |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Current - Supply | 420μA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 115 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~5.5V ±1.2V~2.75V |
| Gain Bandwidth Product | 3MHz |
| Unity Gain BW-Nom | 3000 kHz |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 70μV |
| Current - Output / Channel | 68mA |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Power | NO |
| Voltage Gain-Min | 10000 |
| Height Seated (Max) | 0.67mm |
| RoHS Status | ROHS3 Compliant |
MAX4253EBC+T Overview
In order to protect the op amps, a 12-WFBGA, CSPBGA case is used. Op amps are General Purpose types of amplifier on the chip. A Tape & Reel (TR) case is used for delivering the op amp. The number of terminations is approaching the 10 mark. A total of 10 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. It is recommended that this electronic component be mounted using the Surface Mount mounting type. With regard to operating temperature, this op amp functions well at -40°C~85°C. On this instrumentation amplifier, there are 2 circuits that are connected together. One of its many advantages is that buffer op amp outputs Push-Pull, Rail-to-Rail signals. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. We recommend that you use this electronic part with an 420μA supply in order to get the best performance from it. This operational amplifier can conduct a voltage gain of up to 10000 at a minimum.
MAX4253EBC+T Features
10 Pins
supply voltage of 5V
Output Type: Push-Pull, Rail-to-Rail
MAX4253EBC+T Applications
There are a lot of Maxim Integrated MAX4253EBC+T Instrumentational OP Amps applications.
- Cinema or auditorium audio system
- Subtraction operation circuits
- Band-stop filter
- Broadcasting
- Exponential operation circuits
- Signal operation
- Video conversion and routing
- Polarized electrodes
- MP3
- Division circuits
