MAX4253EUB+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4253 |
| Pin Count | 10 |
| Qualification Status | Not Qualified |
| Output Type | Push-Pull, Rail-to-Rail |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Current - Supply | 420μA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 115 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.4V~5.5V ±1.2V~2.75V |
| Bandwidth | 3MHz |
| Unity Gain BW-Nom | 3000 kHz |
| Average Bias Current-Max (IIB) | 0.0001μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 70μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Power | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
MAX4253EUB+ Overview
Op amp is packaged in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) case. This is a General Purpose type op amp. The op amp is delivered to you in a Tube case. There have been a total of 10 terminations over the past year. Linear amplifier has a total of 10 pins. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 10 pins are located on the operational amplifiers. This electrical part should be mounted using type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~85°C . The buffer amp consists of 2 circuits in total. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Push-Pull, Rail-to-Rail signals. It is recommended that you use an 420μA power supply with this electrical part in order for it to operate correctly.
MAX4253EUB+ Features
10 Pins
supply voltage of 5V
Output Type: Push-Pull, Rail-to-Rail
MAX4253EUB+ Applications
There are a lot of Maxim Integrated MAX4253EUB+ Instrumentational OP Amps applications.
- ECG equipment
- Radar
- Blood pressure sensors
- Subtraction operation circuits
- Information processing
- Proportional counter tubes
- Integrator circuits
- Scintillation detectors
- Weak signal detection
- Non-polarized electrodes
