MAX4330EUK+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4330 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Current - Supply | 275μA |
| Slew Rate | 1.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 87 dB |
| Current - Input Bias | 25nA |
| Voltage - Supply, Single/Dual (±) | 2.3V~6.5V ±1.15V~3.25V |
| Bandwidth | 3MHz |
| Unity Gain BW-Nom | 3000 kHz |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 650μV |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Power | NO |
| Length | 2.9mm |
| RoHS Status | ROHS3 Compliant |
MAX4330EUK+T Overview
There is a SC-74A, SOT-753 case in which the instrumentation amplifier is packaged. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. We are approaching the 5h termination of the year. There are a total of 5 pins on this op amp. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. An 5-pin op amp ic is included in the package. Surface Mount is the recommended mounting type of operational amplifiers. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. On this instrumentation amplifier, there are 1 circuits that are connected together. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. TAPE AND REEL is adopted to pack the instrumentation amplifier. To run supply current of buffer amplifier under 275μA.
MAX4330EUK+T Features
5 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
MAX4330EUK+T Applications
There are a lot of Maxim Integrated MAX4330EUK+T Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Proportional counter tubes
- Large motor controllers
- Addition operation circuits
- Signal filtering
- Video conversion and routing
- Switching amplifier
- High speed sample
- Biopotential
- Vehicle electronics
