MAX4372HESA+T
| Parameters | |
|---|---|
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4372 |
| Pin Count | 8 |
| Output Type | Voltage |
| Supply Voltage-Min (Vsup) | 2.7V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Operating Supply Current | 30μA |
| Nominal Supply Current | 30μA |
| Adjustable Threshold | NO |
| Accuracy | 0.18 % |
| Amplifier Type | Current Sense |
| Common Mode Rejection Ratio | 85 dB |
| Current - Input Bias | 2μA |
| Voltage - Supply, Single/Dual (±) | 2.7V~28V |
| Input Offset Voltage (Vos) | 300μV |
| Supply Current-Max (Isup) | 0.06mA |
| Voltage Gain | 40dB |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| -3db Bandwidth | 110kHz |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 471mW |
MAX4372HESA+T Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. An op amp ic of the Current Sense type. A Tape & Reel (TR) case is used to deliver the buffer op amp. The number of terminations approaches 8. A total of 8 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 12V battery. I would like to specify that this buffer amplifier belongs to the Power Management Circuits-type of devices. The op amp ic has an array of 8 pins on it. The input offset voltage is 300μV. This electrical part should be mounted using type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . An 30μA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain at 40dB. A instrumentation amplifier like this has 1 circuits. There are 1 channels on the operational amplifiers. One of its many advantages is that buffer op amp outputs Voltage signals. The other types of analog IC are as follwed POWER SUPPLY SUPPORT CIRCUIT.
MAX4372HESA+T Features
8 Pins
supply voltage of 12V
40dB voltage gain
Output Type: Voltage
MAX4372HESA+T Applications
There are a lot of Maxim Integrated MAX4372HESA+T Instrumentational OP Amps applications.
- Video conversion and routing
- Automatic control
- Industrial control system
- Polarized electrodes
- single/dual op amp sum and difference circuits
- Division circuits
- Thermocouples
- Differentiator circuits
- Test equipment
- Test and measurement instruments
