MAX4383EEE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 667mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Base Part Number | MAX4383 |
| Pin Count | 16 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 9V |
| Number of Circuits | 4 |
| Operating Supply Current | 7.5mA |
| Slew Rate | 485V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 8.5μA |
| Voltage - Supply, Single/Dual (±) | 4.5V~11V ±2.25V~5.5V |
| Output Current per Channel | 75mA |
| Input Offset Voltage (Vos) | 3mV |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Voltage Gain | 63dB |
| Average Bias Current-Max (IIB) | 25μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Supply Voltage Limit-Max | 6V |
| -3db Bandwidth | 210MHz |
| Height Seated (Max) | 1.75mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4383EEE+ Overview
There is a 16-SSOP (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. There are two types of operational amplifiers in this circuit. Linear amplifier is delivered in a Tube case. The number of terminations is approaching the 16 mark. In this case, there are 16 pins on the board. Please take in mind that op amp should be run at 5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 16 pins are included on the operational amplifiers. In terms of input offset voltage, operational amplifier rates 3mV. The mounting type that is recommended for this electrical part is Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. This op amp can operate from a supply current at 7.5mA. Keeping the voltage gain at 63dB is the best course of action. On this buffer amplifier, there are 4 circuits. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of instrumentation amplifier is rated 9V voltage.
MAX4383EEE+ Features
16 Pins
supply voltage of 5V
63dB voltage gain
Output Type: Rail-to-Rail
MAX4383EEE+ Applications
There are a lot of Maxim Integrated MAX4383EEE+ Instrumentational OP Amps applications.
- Laptop
- Image computer boards
- pH (acidity)
- Portable electronic products powered by batteries
- Proportional counter tubes
- High-frequency data acquisition systems
- Semiconductor detectors
- Proportional operation circuits
- Signal transformation
- Communication device
