MAX44280AXT+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 245mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | MAX44280 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Operating Supply Current | 750μA |
| Nominal Supply Current | 750nA |
| Output Current | 85mA |
| Slew Rate | 30V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 0.01pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 85mA |
| Input Offset Voltage (Vos) | 10μV |
| Bandwidth | 50MHz |
| Unity Gain BW-Nom | 50000 kHz |
| Voltage Gain | 115dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 5e-7μA |
| Length | 2mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX44280AXT+T Overview
There is a 6-TSSOP, SC-88, SOT-363 case package that contains the instrumentation amplifiers. Op amps are General Purpose types of amplifier on the chip. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be 6 terminations in the next few months. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3.3V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. A total of 6 pins are present on the instrumentation amplifier. There is an input offset voltage of 10μV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~125°C. As long as the supply current of the chip does not exceed 750μA, this op amp ic can operate. 115dB should be the voltage gain. Instrumentation amplifier has 1 channels on it. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.
MAX44280AXT+T Features
supply voltage of 3.3V
115dB voltage gain
Output Type: Rail-to-Rail
MAX44280AXT+T Applications
There are a lot of Maxim Integrated MAX44280AXT+T Instrumentational OP Amps applications.
- Differentiator circuits
- Power generator
- Cinema or auditorium audio system
- Fission chambers
- Division circuits
- Comparator
- Digital cameras
- Video amplifiers
- PDA
- Hand-held batteries
