Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
-40°C~85°C |
Packaging |
Tube |
Published |
2011 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Operational Amplifier |
Technology |
BICMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4474 |
Pin Count |
8 |
JESD-30 Code |
R-PDSO-G8 |
Output Type |
Rail-to-Rail |
Number of Circuits |
2 |
Operating Supply Current |
750nA |
Nominal Supply Current |
750nA |
Output Current |
11mA |
Slew Rate |
0.02V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
70 dB |
Current - Input Bias |
200pA |
Voltage - Supply, Single/Dual (±) |
1.8V~5.5V |
Output Current per Channel |
36mA |
Input Offset Voltage (Vos) |
500μV |
Gain Bandwidth Product |
40kHz |
Unity Gain BW-Nom |
40 kHz |
Voltage Gain |
120dB |
Low-Offset |
NO |
Frequency Compensation |
YES AVCL>=5 |
Supply Voltage Limit-Max |
6V |
Low-Bias |
NO |
Micropower |
YES |
Bias Current-Max (IIB) @25C |
0.0015μA |
Programmable Power |
NO |
Wideband |
NO |
Power |
NO |
Height Seated (Max) |
1.75mm |
Length |
4.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4474ESA Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. This is a General Purpose type op amp. The op amp is delivered to you in a Tube case. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 5V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. Op amp rates 500μV as input offset voltage. This electronic part is best mounted with type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . You can run this op amp ic on 750nA . 120dB should be the voltage gain. On this buffer amplifier, there are 2 circuits. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals.
MAX4474ESA Features
8 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
MAX4474ESA Applications
There are a lot of Maxim Integrated MAX4474ESA Instrumentational OP Amps applications.
- Signal filtering
- Band-pass filter
- Television broadcasting equipment
- Test equipment
- Commercial audio systems
- Division circuits
- earphone
- Multimedia playback equipment
- Professional videography
- Medical imaging