MAX4475AUT+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4475 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Current - Supply | 2.5mA |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 115 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 70μV |
| Current - Output / Channel | 48mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Power | NO |
| Length | 2.9mm |
| RoHS Status | ROHS3 Compliant |
MAX4475AUT+T Overview
It is packaged in an SOT-23-6-case that protects the operational amplifiers from damage. An op amp ic of the General Purpose type. The op amp is delivered to you in a Tape & Reel (TR) case. A total of 6 terminations have been reported in the past few weeks. In total, there are 6 pins on this op amp ic. It is important to remember that this op amp should be operated at a voltage of 3V volts. To be specific, this instrumentation amplifier is a type of Operational Amplifier. In total, the buffer amplifier consists of 6 pins. This electronic part is recommended for mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. On this buffer amplifier, there are 1 circuits. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. The instrumentation amplifier is packed in the form of TAPE AND REEL. There is a recommendation that this electrical part be used with a supply with 2.5mA current rating.
MAX4475AUT+T Features
6 Pins
supply voltage of 3V
Output Type: Rail-to-Rail
MAX4475AUT+T Applications
There are a lot of Maxim Integrated MAX4475AUT+T Instrumentational OP Amps applications.
- Vehicle electronics
- Car stereo
- Automation control systems
- Proportional operation circuits
- Wireless base stations
- Non-polarized electrodes
- Semiconductor detectors
- Exponential operation circuits
- Gaming industry
- single/dual op amp sum and difference circuits
